Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Tamko Flashing Replacement: The Winchester Owner’s Guide
Tamko flashing replacement in Winchester typically runs $285 to $640 installed for a standard roof-to-wall or chimney flashing assembly, and most jobs are done in a single visit once we’ve matched the right profile to your roof. We install Tamko-compatible flashing alongside GAF, Owens Corning, and CertainTeed systems, and we’re an independent roofing company, not affiliated with Tamko.

Owners in Winchester usually find the problem the same way: a brown ring on the ceiling after a hard rain, a curl of rust-colored stain running down the siding, or a roofing nail popping loose where the metal meets the shingle course. Maybe a neighbor points it out first. That’s fine too. The flashing is the metal that seals every seam the shingles can’t cover by themselves, and in Winchester it takes the worst of the weather.
Which Tamko Models This Applies To
Tamko flashing isn’t a single product line, so matching the part to your roof matters more than it does with some brands. The two you’ll run into most on Winchester homes are the Tamko LMR (low-moderate roof) roll flashing, used along walls and sidewalls where the pitch is shallow, and Tamko prebent step flashing in 5-inch and 7-inch legs. If your roof is steep or the flashing sits at a chimney or penetration, you’re likely looking at a piece cut from coil stock rather than a preformed unit, and that’s where the measurement gets specific.
To identify what you have, look at the top leg return before anything else. Tamko step flashing runs 4-inch, 5-inch, and 7-inch legs, and a wrong-leg piece will either telegraph through the shingles or leave a gap behind the siding. Check the gauge too. Most residential flashing here is 26-gauge galvanized or a painted aluminum, and if a prior roofer used 30-gauge coil, a 26-gauge replacement won’t sit flush. When you call, give us the leg measurement, the gauge if you know it, and a photo of where the seam meets the wall. That’s how we source the right part the first time.
OEM or aftermarket? For Tamko flashing specifically, an OEM piece is worth it when the flashing runs a long wall or a chimney where the return has to lock into a shingle course exactly. For a short penetration boot or a small sidewall run, a quality aftermarket flashing from a name manufacturer does the same job at a lower number, and we’ll tell you which is which on your roof instead of upselling the OEM by default.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your Tamko Flashing Replacement Is Failing
Flashing fails before the shingles do, so the warning signs show up early if you know where to look. Here’s what we see on Tamko flashing in Winchester, and what’s actually causing each one.
- Rust streaks on the metal or siding. Galvanized flashing oxidizes where the coating has failed, often at a cut edge or a nail hole, and the stain runs downhill. Rust means the protective layer is gone and the piece needs replacement, not a coat of paint.
- Lifted or curling shingle edges along the flashing. Sun and heat break the seal where the shingle meets the metal, and a small lift lets water wick back under the course. That’s the beginning of a leak you can’t see from the ground.
- Water stains on the ceiling or wall below. This is the tell that water has already gotten past the flashing and is traveling along framing. A stain on a Winchester ceiling after rain almost always points back to a flashing seam or a nail hole above it.
- Gaps, pulled fasteners, or loose step flashing. Thermal movement over the years pulls step flashing a hair away from the wall, and once the gap opens, the wind-driven rain gets in. Look for daylight or a visible slit at the wall junction.
- Granules and grit in the gutters below the flashing. Shingle granules collecting under a flashing run mean the metal has been abrading the shingle edge, which usually points to a poorly matched or badly seated piece from the start.
If two or more of these show up in the same area, the flashing and the shingle course above it have likely both been compromised, and a repair to the metal alone won’t hold.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what Tamko-compatible flashing replacement runs in Winchester, installed, with the parts-and-labor broken out the way we’d want it if we were the ones writing the check:

| Scope | Installed Range |
|---|---|
| Single sidewall run (up to 10 ft), Tamko LMR or step flashing | $285 – $420 |
| Chimney flashing assembly (front, back, and side steps) | $440 – $640 |
| Skylight or pipe penetration boot and flashing | $310 – $480 |
| Full wall-to-wall run with step flashing, 25+ ft | $580 – $960 |
What drives the range: the length of the run, the gauge and material you choose, how much shingle has to come up to seat the flashing correctly, and whether the deck underneath is sound or needs a patch. We pull the old piece, look at the deck, and hand you a written line-item quote with the part number, the footage, and the labor split. If a bidder won’t itemize the part, ask why. Every flashing job we do carries the written 90-Day Done Right Promise and a free second opinion on any written estimate before you commit. No trip charge inside our own county.
DIY or Call Us?
You can safely check your own flashing from the ground or out a second-story window. Look for rust, lifted shingle edges, a visible gap at the wall, or stain lines on the siding, and take a photo with your phone zoomed in. That’s a real help when you call, because a photo of the seam tells us more than a description.
What I’d steer you away from is climbing up to reseat flashing yourself. It’s not the danger of high-tension work like a garage-door spring, but a roof is still a fall hazard, and flashing has to be woven into the shingle course in the right order or it’ll leak worse than before. The fasteners, the sealant, and the step sequence all have to be right, and a homeowner doing it from a ladder usually can’t see the return under the siding. The other trap is sealing a failed piece with caulk or tar. That buys you one season in Winchester, tops, and the water finds a new path.
If you’re not sure whether it’s the flashing or the shingle above it, call (844) 797-8167 and we’ll look at it with you. A live person answers the phone, day or night, and we’ll tell you straight whether it’s a flashing swap or a bigger repair. We’re an independent shop, so the call is about your roof, not a sales target.
FAQs
Galvanized Tamko flashing typically gives you 20 to 30 years in this climate, and painted aluminum runs closer to 25 to 35 if it’s installed with the cut edges sealed. Northern Nevada swings from hard summer UV to freezing winter nights, and that thermal cycling works the metal at every fastener and seam, which is why a flashing that looks fine on top can fail at the edges first. If yours is past the 20-year mark and showing rust at a cut edge, plan on replacement rather than repair. Call (844) 797-8167 for an exact quote, and the estimate is free.
Sometimes, yes. A single pulled step flashing can be reseated and re-fastened, and a small sidewall gap can be reset if the metal itself is still sound. What can’t be honestly repaired is rust-through, a cracked or creased piece, or flashing that was the wrong gauge to begin with. In those cases, patching is money thrown at a piece that’s already past its life, and we’ll tell you which situation you’re in before we quote. Call (844) 797-8167 for a free second opinion.
Most single-run Tamko flashing replacements take two to four hours, and a chimney assembly usually fills half a day. If the shingle course above has to come up to seat the new piece correctly, add a couple hours. We’ll give you the timeline in the written quote so you know what to expect, and we won’t leave a tear-open overnight. Call (844) 797-8167 to get on the schedule.
We order to the measurements from your roof, not from a guess. Give us the leg measurement, the gauge, and a photo of the seam, and we’ll match the Tamko profile or the correct quality equivalent and bring it to the job. We don’t claim to carry Tamko parts on a truck or keep a stock of them, so the piece comes in sized for your roof. That’s how the install stays clean and the price stays on the quote. Call (844) 797-8167 to set up your free estimate.
We’re Shepherd & Sons Roofing Winchester, locally owned and owner-operated, and flashing work is one of the repairs we’ve handled on Winchester roofs since the 1990s. If Tamko flashing on your roof is failing, or you just want a straight answer on whether it’s the metal or the shingle, give us a call. Ask anyone on your street. The name on the truck is the name on the license.
Written by the team at Shepherd & Sons Roofing Winchester, serving Winchester and nearby areas.