Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Boral Flashing Replacement: The Winchester Owner’s Guide
Replacing failed Boral flashing in Winchester typically runs $410 to $880 installed, depending on the flashing type, how much length has to come out, and whether the job touches the field tile. We install and replace Boral-compatible flashing, and we can usually get out to look at yours within a day or two of your call. Most owners find out they have a problem the same way: a brown water stain spreads across a ceiling in the spare bedroom, or they spot a strip of metal lifted up along the roofline after a wind event and think, “how long has that been like that?” Boral flashing is the metal that seals the joints where water wants in, and when it fails in Winchester’s heat, it fails quietly.

Which Boral Models This Applies To
Boral’s concrete and clay roof tile lines cover a lot of ground, from the flat-profile tiles that dominate so many Winchester roofs to the barrel and high-profile shapes. Flashing for each is not interchangeable. A barrel-tile valley uses a much deeper, wider pan than a flat-profile valley, because the tile itself sits higher off the deck. Buy the wrong profile and you get a flashing that looks installed but sheds water under the laps instead of over them.
The way to match right: read the label inside the channel of a spare tile (Boral stamps the series there), or measure a tile’s exact width, thickness and the height of its curve. That measurement, not the color or the look, is what decides which flashing works. On the OEM-versus-aftermarket call, we don’t push one. Factory Boral flashing typically uses a specific aluminum or copper gauge spec matched to the tile, and it’s the surest fit. A good roll-form shop can bend a quality equivalent to the same profile and thickness for less, and on a repair rather than a full build, that’s often the smarter buy. What matters is the metal and the bend, not the box it came in.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your Boral Flashing Replacement Is Failing
Flashing doesn’t wear out in one dramatic moment. It goes in stages, and here’s what each stage looks like:
- Water staining on a ceiling or wall near a roof joint. This is the classic late-stage signal. Water has been getting past a lifted or cracked seam for a while and finally found its way down.
- Lifted, curled or delaminated edges. Wind and thermal cycling peel the metal back from where it’s supposed to lap. In Winchester, the summer swing from cool mornings to 110-degree afternoons works the metal hard, and that fatigue shows first at the edges.
- Rust spots, pitting or white powdery corrosion. The wrong metal, or the right metal the wrong way, gives up faster than it should. Once it’s pitted through, patching is a waste of money.
- Gaps at the wall, chimney or valley. Sealant dries out and pulls away from the metal. A visible gap is a direct path for water.
- Granule or dirt lines running down the tile from a joint. This sounds minor, but it’s a reliable early clue that water is channeling where it shouldn’t be. Catching it here means a much smaller job.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the honest range for Winchester, with the parts-and-labor split built in:
- Single wall or step flashing run: $410 to $620 installed
- Valley flashing, one run: $550 to $880 installed
- Chimney or skylight surround: $620 to $950 installed, more if tile has to come up
What drives the range is how many tiles have to come out to reach the flashing, the metal you choose (aluminum versus copper), and how much of the surrounding underlayment has to be replaced with it. We don’t hide the parts markup: you see the flashing spec and the labor as separate lines, and the price is the price. The work is backed by our written 90-Day Done Right Promise, and the job comes with a written, line-item quote before anyone touches your roof.

DIY or Call Us?
You can safely check a few things yourself. Walk the roof from the ground with binoculars, or stand back under the eave and look for lifted edges, rust, and gaps at the wall. Take a photo. What you shouldn’t do is climb up and start prying tile to reach the flashing. Boral concrete tile is heavy and brittle, and a cracked tile you didn’t plan for turns a $500 repair into a much bigger bill. The bigger risk is working at height on a steep or wet roof, and water that gets in behind a half-finished flashing job is worse than keeping the old one.
What needs a trained eye is the diagnosis: which flashing failed, how far the water traveled, and whether the underlayment behind it is still good. That’s the part we’ll do with you. Call (844) 797-8167 and we’ll come look, with no trip charge inside our county.
FAQs
A properly installed aluminum flashing often gets 20 to 30 years, and copper runs considerably longer, but in Winchester’s sun and heat, exposed sealant at the joints dries out in 5 to 8 years and needs refreshing. The metal itself usually outlasts the sealant around it, which is why catching a failed seam early saves you money.
Sometimes, yes. If the failure is a single lifted edge or dried sealant, resealing and re-lapping can buy you several more years. If the metal is rusted through, cracked, or the wrong profile was used to begin with, replacement is the only fix that actually stops the leak. We’ll tell you which one you’re looking at, and we won’t sell a replacement job when a repair will do it.
A single wall or step flashing run is usually a half-day job. Valley or chimney flashing that requires lifting tile typically takes a full day, occasionally two if old underlayment has to be replaced. We give you the timeline up front in the written estimate, and a live person answers the phone when you call, not a call center.
We match the flashing to your tile profile by measurement and label, then get the right aluminum or copper spec, either through Boral’s supply or a local roll-form shop that bends to the same profile. We’re an independent service provider, not affiliated with Boral, so the part we recommend is the one that fits your roof, not the one that’s easiest to sell. We install products from GAF, CertainTeed and Owens Corning too, so a mixed roof is no problem.
Call (844) 797-8167 to schedule your free estimate. We’ll show you the deck photos and give you a written, line-item quote before we talk money, because a flashing job in Winchester should come with a straight number and a name you can look up.
Written by the team at Shepherd & Sons Roofing Winchester, serving Winchester and nearby areas.