Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
CertainTeed Flashing Replacement: The Winchester Owner’s Guide
We replace failed CertainTeed flashing with compatible components, and most Winchester jobs land between $340 and $780 installed depending on where the flashing sits and how much surrounding roofing has to come up to reach it. Diagnosis and a written quote are free, and we can usually get out to look at it within a few days of your call. We’re an independent contractor and not affiliated with CertainTeed, though flashing around a CertainTeed roof behaves the same way ours does.

Most Winchester owners don’t go looking for flashing. They find it the same way: a brown water stain spreading across a ceiling during a monsoon, or a roofer up on a repair pointing at a gap. Our technicians have up to 30 years of experience and have pulled flashing off plenty of CertainTeed installations, so the failure usually reads clearly once we’re on the roof.
Which CertainTeed Models This Applies To
CertainTeed doesn’t sell flashing as a branded part, and that surprises people. The company makes underlayment, shingles, and accessories like their SwiftStart and WinterGuard lines, but the actual metal flashing around a chimney, a wall corner, or a vent stack is unbranded metal that a crew bent on site. So when we say we’re matching a CertainTeed roof, we mean we’re matching the flashing to the specific shingle line: Landmark, Landmark Pro, Presidential Shake, and the rest, because the shingle profile and thickness change how deep the flashing sits and how the cap gets dressed.
Finding the right match
Look for the shingle wrapper or a scrap left in the garage. It’ll name the line and often the color. On the roof, we measure the exposed reveal: Landmark runs about 5-5/8″ to the weather, and Presidential Shake is a thicker, heavier profile that demands taller step flashing to clear the course above it. Get the shingle line wrong and the flashing sits proud or short, and either way the wind and rain find the seam.
Original flashing versus a quality equivalent
There is no CertainTeed part number to hunt down, which actually makes the decision easier. We bend step flashing and counter-flashing from 26-gauge galvanized or the heavier 24-gauge, and on a taller chimney we’ll run copper because it lasts longer against our sun. Cheap pre-bent flashing from a big box store is thinner metal that oil-cans and pulls loose. That’s the difference that matters, not a brand on the wrapper.
Styles & brands we work with
- Architectural shingles
- Metal roofing
- Tile roofing
- GAF
- Owens Corning
- Flat & low-slope
Signs Your CertainTeed Flashing Replacement Is Failing
Flashing fails differently on a CertainTeed roof here than it does in wetter climates, mostly because our sun and our seasonal swings do the damage faster than rain alone. Watch for these five.
- Rust streaks running down the shingles below a chimney or wall. The galvanized coating has broken down, which happens quickly under Winchester’s summer sun and long stretches without rain. Once the coating fails, the metal starts pitting through.
- Caulk lines pulling away at a wall corner. Sealant is a stopgap, not a fix. In our heat, caulk shrinks and cracks within a year or two, and every crack is a path for monsoon rain. Somebody probably caulked it once and the problem moved underneath.
- Water staining on the ceiling near an outside wall or the chimney. This is how you know it’s already leaked. Staining near an exterior wall usually points to step flashing that lost its lap, not a bad shingle field.
- Lifted or wavy step flashing under the shingles. Shingles that have curled or settled as the roof aged can pull the flashing out of its lap, and wind catches the gap. When shingles go up, the flashing has to go with them or you’re leaving an opening. This is why I like to see deck photos before we talk money, so the cause is clear and not a guess.
- Gaps at a vent pipe boot that’s hardened and cracked. The rubber collar around a pipe hardens like a knee pad left in the sun. Once it cracks, water runs straight down the pipe. A boot gets mistaken for flashing all the time, and the fix is the same kind of visit.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the honest range for a flashing replacement in Winchester:

- Vent pipe boot swap, single pipe: $180 to $320 installed.
- Step flashing along a wall corner or dormer, under 12 linear feet: $340 to $560 installed.
- Chimney flashing, including the counter-flashing and the lap into the masonry: $520 to $980 installed, higher when the chimney is wide or the masonry has to be cut back and re-sealed.
- Skylight flashing rebuild: $450 to $850 installed.
The range is driven by how many courses of shingles have to come up to reach a clean lap, the metal used, and how high or steep the access is. Labor is most of the number on smaller jobs, and we show the parts and labor as separate line items so you can see what you’re paying for. Every job here carries our written 90-Day Done Right Promise. If something we touched leaks, you call and Bill comes back. Free second opinion on any written estimate you’ve collected, and no trip charge inside our own county.
DIY or Call Us?
You can safely do a few things from the ground. Look at the ceiling for stains, check for rust streaks or cracked caulk without ever getting on the roof, and read the shingle wrapper to find the CertainTeed line. That information helps us quote correctly.
The part that gets people in trouble is getting on the roof at all. A two-story Winchester house with a pitched roof and our afternoon heat is a bad combination, and the fall risk is real. Add that pulling flashing means breaking the seal under the shingles above it, and a botched DIY job usually leaks worse than it started. We’d rather you call. Dial (844) 797-8167 and a live person answers, day or night.
FAQs
Galvanized flashing on a Winchester roof typically lasts 15 to 20 years before rust gets ahead of it, while copper or a heavier step flashing can push much longer. Our sun cooks the galvanized coating faster than a damper climate would, so the metal ages ahead of the shingles that surround it.
Sometimes, yes, and it depends on how much of the lap has lost its seal. A short section of step flashing can be re-lapped and re-caulked as a stopgap, but rusted-through or pulled metal needs replacement because a patch won’t hold through a monsoon. We tell you which one you’re facing after we look, and we don’t sell a replacement you don’t need. Call (844) 797-8167 for a free estimate.
Most flashing replacements take two to four hours on the roof once we’re set up, and a simple vent boot can be done inside an hour. A chimney rebuild can run most of a day if the counter-flashing has to be cut back and the masonry re-sealed. We’ll tell you the timing before we start so you’re not guessing.
We bend step flashing and counter-flashing to fit your specific CertainTeed shingle line rather than ordering a pre-made piece. Since CertainTeed doesn’t sell branded flashing, we measure the shingle profile and lay the metal so it laps correctly, using 26-gauge galvanized or heavier. If it’s a vent boot, we match the pipe diameter and the brand of boot that fits the shingle reveal. We also install products from GAF and Owens Corning, so if your flashing sits near a different shingle line, we’ve set it.
If your CertainTeed roof in Winchester is showing rust streaks or a ceiling stain, don’t wait for the next storm. Call (844) 797-8167 to schedule your free estimate, and a live person will pick up.
Written by the team at Shepherd & Sons Roofing Winchester, serving Winchester and nearby areas.